Contact us if you need professional support or have any questions
Ann Idstein AB
Dalby 541, DALBY, Sweden
Phone +46 46 14 03 70
info@annidstein.com
Download
Fitting to a wall or ceiling
Before you measure
Start by checking that the surface is suitable for the purpose of fitting a blind. Make sure that fittings can be properly attached and that the surface is strong enough to carry the weight of the product. The surface should be even and it is important that the measuring points you are considering, are well aligned.
Width measurement
1. When fitting a free hanging product:
Measure the desired width of the ready made product and use
this measurement as your system width when ordering.
2. When fitting a product from wall to wall:
Measure the width at three points; at the top, in the middle
and at the bottom. If the measurements deviate, please use the
smallest one and deduct according to the chart below, in order
to calculate your system width. When measuring for Roller
Blinds, it is sufficient to measure the width at the top.
Height measurement
1. When fitting a free hanging product:
Measure the height from the ceiling or from a point on the wall
to the point where you want the lower edge of the product to
be. Use this measurement as your system height.
2. When fitting a product from wall to wall:
Measure the height at three points; to the left, in the middle
and on the right. If the measurements deviate, please use the
smallest one and deduct according to the chart below, in order
to calculate your system height.
| Recommended deductions | Width | Height |
|---|---|---|
| Panel System | -10 mm | -15 mm |
| Roller Blinds | -5 mm | -0 mm |
| System R & Vertical Blinds | -10 mm | -20 mm |
| System W | -5 mm | -0 mm |
| Venetian Blinds | -10 mm | ** |
** The production height of Venetian Blinds is dependent on the pitch within the ladder cords and therefore, an exact height cannot be guaranteed. You can choose to order by sending us your height measurement without deduction and letting us know whether you prefer your blind to be ”Plus”, meaning that the blind will be at least as high as the height measurement prior to deduction or ”Minus” if you want to make sure that the blind is guaranteed not to sit on the floor, window board etc. when pulled down.
Fitting in a recess
Before you measure
Start by checking that the surface is suitable for the purpose of fitting a blind. Make sure that fittings can be properly attached and that the surface is strong enough to carry the weight of the product. The surface should be even and it is important that the measuring points you are considering, are well aligned.
Width measurement
Measure the width at three points; at the top, in the middle and at the bottom. If the measurements deviate, please use the smallest one and deduct according to the chart below, in order to calculate your system width. When measuring for Roller Blinds, it is sufficient to measure the width at the top.
Height measurement
Measure the height at three points; to the left, in the middle and on the right. If the measurements deviate, please use the smallest one and deduct according to the chart below, in order to calculate your system height.
| Recommended deductions | Width | Height |
|---|---|---|
| Panel System | -10 mm | -15 mm |
| Roller Blinds | -5 mm | -0 mm |
| System R & Vertical Blinds | -10 mm | -20 mm |
| System W | -5 mm | -0 mm |
| Venetian Blinds | -10 mm | ** |
** The production height of Venetian Blinds is dependent on the pitch within the ladder cords and therefore, an exact height cannot be guaranteed. You can choose to order by sending us your height measurement without deduction and letting us know whether you prefer your blind to be ”Plus”, meaning that the blind will be at least as high as the height measurement prior to deduction or ”Minus” if you want to make sure that the blind is guaranteed not to sit on the floor, window board etc. when pulled down.
Ann Idstein AB
Dalby 541, DALBY, Sweden
Phone +46 46 14 03 70
info@annidstein.com
Material
Fitting to a wall or ceiling
Before you measure
Start by checking that the surface is suitable for the purpose of fitting a blind. Make sure that fittings can be properly attached and that the surface is strong enough to carry the weight of the product. The surface should be even and it is important that the measuring points you are considering, are well aligned.
Width measurement
1. When fitting a free hanging product:
Measure the desired width of the ready made product and use
this measurement as your system width when ordering.
2. When fitting a product from wall to wall:
Measure the width at three points; at the top, in the middle
and at the bottom. If the measurements deviate, please use the
smallest one and deduct according to the chart below, in order
to calculate your system width. When measuring for Roller
Blinds, it is sufficient to measure the width at the top.
Height measurement
1. When fitting a free hanging product:
Measure the height from the ceiling or from a point on the wall
to the point where you want the lower edge of the product to
be. Use this measurement as your system height.
2. When fitting a product from wall to wall:
Measure the height at three points; to the left, in the middle
and on the right. If the measurements deviate, please use the
smallest one and deduct according to the chart below, in order
to calculate your system height.
| Recommended deductions | Width | Height |
|---|---|---|
| Panel System | -10 mm | -15 mm |
| Roller Blinds | -5 mm | -0 mm |
| System R & Vertical Blinds | -10 mm | -20 mm |
| System W | -5 mm | -0 mm |
| Venetian Blinds | -10 mm | ** |
** The production height of Venetian Blinds is dependent on the pitch within the ladder cords and therefore, an exact height cannot be guaranteed. You can choose to order by sending us your height measurement without deduction and letting us know whether you prefer your blind to be ”Plus”, meaning that the blind will be at least as high as the height measurement prior to deduction or ”Minus” if you want to make sure that the blind is guaranteed not to sit on the floor, window board etc. when pulled down.
Fitting in a recess
Before you measure
Start by checking that the surface is suitable for the purpose of fitting a blind. Make sure that fittings can be properly attached and that the surface is strong enough to carry the weight of the product. The surface should be even and it is important that the measuring points you are considering, are well aligned.
Width measurement
Measure the width at three points; at the top, in the middle and at the bottom. If the measurements deviate, please use the smallest one and deduct according to the chart below, in order to calculate your system width. When measuring for Roller Blinds, it is sufficient to measure the width at the top.
Height measurement
Measure the height at three points; to the left, in the middle and on the right. If the measurements deviate, please use the smallest one and deduct according to the chart below, in order to calculate your system height.
| Recommended deductions | Width | Height |
|---|---|---|
| Panel System | -10 mm | -15 mm |
| Roller Blinds | -5 mm | -0 mm |
| System R & Vertical Blinds | -10 mm | -20 mm |
| System W | -5 mm | -0 mm |
| Venetian Blinds | -10 mm | ** |
** The production height of Venetian Blinds is dependent on the pitch within the ladder cords and therefore, an exact height cannot be guaranteed. You can choose to order by sending us your height measurement without deduction and letting us know whether you prefer your blind to be ”Plus”, meaning that the blind will be at least as high as the height measurement prior to deduction or ”Minus” if you want to make sure that the blind is guaranteed not to sit on the floor, window board etc. when pulled down.
Ann Idstein AB
Dalby 541, DALBY, Sweden
Phone +46 46 14 03 70
info@annidstein.com
Material
Fitting to a wall or ceiling
Before you measure
Start by checking that the surface is suitable for the purpose of fitting a blind. Make sure that fittings can be properly attached and that the surface is strong enough to carry the weight of the product. The surface should be even and it is important that the measuring points you are considering, are well aligned.
Width measurement
1. When fitting a free hanging product:
Measure the desired width of the ready made product and use
this measurement as your system width when ordering.
2. When fitting a product from wall to wall:
Measure the width at three points; at the top, in the middle
and at the bottom. If the measurements deviate, please use the
smallest one and deduct according to the chart below, in order
to calculate your system width. When measuring for Roller
Blinds, it is sufficient to measure the width at the top.
Height measurement
1. When fitting a free hanging product:
Measure the height from the ceiling or from a point on the wall
to the point where you want the lower edge of the product to
be. Use this measurement as your system height.
2. When fitting a product from wall to wall:
Measure the height at three points; to the left, in the middle
and on the right. If the measurements deviate, please use the
smallest one and deduct according to the chart below, in order
to calculate your system height.
| Recommended deductions | Width | Height |
|---|---|---|
| Panel System | -10 mm | -15 mm |
| Roller Blinds | -5 mm | -0 mm |
| System R & Vertical Blinds | -10 mm | -20 mm |
| System W | -5 mm | -0 mm |
| Venetian Blinds | -10 mm | ** |
** The production height of Venetian Blinds is dependent on the pitch within the ladder cords and therefore, an exact height cannot be guaranteed. You can choose to order by sending us your height measurement without deduction and letting us know whether you prefer your blind to be ”Plus”, meaning that the blind will be at least as high as the height measurement prior to deduction or ”Minus” if you want to make sure that the blind is guaranteed not to sit on the floor, window board etc. when pulled down.
Fitting in a recess
Before you measure
Start by checking that the surface is suitable for the purpose of fitting a blind. Make sure that fittings can be properly attached and that the surface is strong enough to carry the weight of the product. The surface should be even and it is important that the measuring points you are considering, are well aligned.
Width measurement
Measure the width at three points; at the top, in the middle and at the bottom. If the measurements deviate, please use the smallest one and deduct according to the chart below, in order to calculate your system width. When measuring for Roller Blinds, it is sufficient to measure the width at the top.
Height measurement
Measure the height at three points; to the left, in the middle and on the right. If the measurements deviate, please use the smallest one and deduct according to the chart below, in order to calculate your system height.
| Recommended deductions | Width | Height |
|---|---|---|
| Panel System | -10 mm | -15 mm |
| Roller Blinds | -5 mm | -0 mm |
| System R & Vertical Blinds | -10 mm | -20 mm |
| System W | -5 mm | -0 mm |
| Venetian Blinds | -10 mm | ** |
** The production height of Venetian Blinds is dependent on the pitch within the ladder cords and therefore, an exact height cannot be guaranteed. You can choose to order by sending us your height measurement without deduction and letting us know whether you prefer your blind to be ”Plus”, meaning that the blind will be at least as high as the height measurement prior to deduction or ”Minus” if you want to make sure that the blind is guaranteed not to sit on the floor, window board etc. when pulled down.
Ann Idstein AB
Dalby 541, DALBY, Sweden
Phone +46 46 14 03 70
info@annidstein.com
Material
Fitting to a wall or ceiling
Before you measure
Start by checking that the surface is suitable for the purpose of fitting a blind. Make sure that fittings can be properly attached and that the surface is strong enough to carry the weight of the product. The surface should be even and it is important that the measuring points you are considering, are well aligned.
Width measurement
1. When fitting a free hanging product:
Measure the desired width of the ready made product and use
this measurement as your system width when ordering.
2. When fitting a product from wall to wall:
Measure the width at three points; at the top, in the middle
and at the bottom. If the measurements deviate, please use the
smallest one and deduct according to the chart below, in order
to calculate your system width. When measuring for Roller
Blinds, it is sufficient to measure the width at the top.
Height measurement
1. When fitting a free hanging product:
Measure the height from the ceiling or from a point on the wall
to the point where you want the lower edge of the product to
be. Use this measurement as your system height.
2. When fitting a product from wall to wall:
Measure the height at three points; to the left, in the middle
and on the right. If the measurements deviate, please use the
smallest one and deduct according to the chart below, in order
to calculate your system height.
| Recommended deductions | Width | Height |
|---|---|---|
| Panel System | -10 mm | -15 mm |
| Roller Blinds | -5 mm | -0 mm |
| System R & Vertical Blinds | -10 mm | -20 mm |
| System W | -5 mm | -0 mm |
| Venetian Blinds | -10 mm | ** |
** The production height of Venetian Blinds is dependent on the pitch within the ladder cords and therefore, an exact height cannot be guaranteed. You can choose to order by sending us your height measurement without deduction and letting us know whether you prefer your blind to be ”Plus”, meaning that the blind will be at least as high as the height measurement prior to deduction or ”Minus” if you want to make sure that the blind is guaranteed not to sit on the floor, window board etc. when pulled down.
Fitting in a recess
Before you measure
Start by checking that the surface is suitable for the purpose of fitting a blind. Make sure that fittings can be properly attached and that the surface is strong enough to carry the weight of the product. The surface should be even and it is important that the measuring points you are considering, are well aligned.
Width measurement
Measure the width at three points; at the top, in the middle and at the bottom. If the measurements deviate, please use the smallest one and deduct according to the chart below, in order to calculate your system width. When measuring for Roller Blinds, it is sufficient to measure the width at the top.
Height measurement
Measure the height at three points; to the left, in the middle and on the right. If the measurements deviate, please use the smallest one and deduct according to the chart below, in order to calculate your system height.
| Recommended deductions | Width | Height |
|---|---|---|
| Panel System | -10 mm | -15 mm |
| Roller Blinds | -5 mm | -0 mm |
| System R & Vertical Blinds | -10 mm | -20 mm |
| System W | -5 mm | -0 mm |
| Venetian Blinds | -10 mm | ** |
** The production height of Venetian Blinds is dependent on the pitch within the ladder cords and therefore, an exact height cannot be guaranteed. You can choose to order by sending us your height measurement without deduction and letting us know whether you prefer your blind to be ”Plus”, meaning that the blind will be at least as high as the height measurement prior to deduction or ”Minus” if you want to make sure that the blind is guaranteed not to sit on the floor, window board etc. when pulled down.
Ann Idstein AB
Dalby 541, DALBY, Sweden
Phone +46 46 14 03 70
info@annidstein.com
Ann Idstein AB
Dalby 541, DALBY, Sweden
Phone +46 46 14 03 70
info@annidstein.com
Material
Fitting to a wall or ceiling
Before you measure
Start by checking that the surface is suitable for the purpose of fitting a blind. Make sure that fittings can be properly attached and that the surface is strong enough to carry the weight of the product. The surface should be even and it is important that the measuring points you are considering, are well aligned.
Width measurement
1. When fitting a free hanging product:
Measure the desired width of the ready made product and use
this measurement as your system width when ordering.
2. When fitting a product from wall to wall:
Measure the width at three points; at the top, in the middle
and at the bottom. If the measurements deviate, please use the
smallest one and deduct according to the chart below, in order
to calculate your system width. When measuring for Roller
Blinds, it is sufficient to measure the width at the top.
Height measurement
1. When fitting a free hanging product:
Measure the height from the ceiling or from a point on the wall
to the point where you want the lower edge of the product to
be. Use this measurement as your system height.
2. When fitting a product from wall to wall:
Measure the height at three points; to the left, in the middle
and on the right. If the measurements deviate, please use the
smallest one and deduct according to the chart below, in order
to calculate your system height.
| Recommended deductions | Width | Height |
|---|---|---|
| Panel System | -10 mm | -15 mm |
| Roller Blinds | -5 mm | -0 mm |
| System R & Vertical Blinds | -10 mm | -20 mm |
| System W | -5 mm | -0 mm |
| Venetian Blinds | -10 mm | ** |
** The production height of Venetian Blinds is dependent on the pitch within the ladder cords and therefore, an exact height cannot be guaranteed. You can choose to order by sending us your height measurement without deduction and letting us know whether you prefer your blind to be ”Plus”, meaning that the blind will be at least as high as the height measurement prior to deduction or ”Minus” if you want to make sure that the blind is guaranteed not to sit on the floor, window board etc. when pulled down.
Fitting in a recess
Before you measure
Start by checking that the surface is suitable for the purpose of fitting a blind. Make sure that fittings can be properly attached and that the surface is strong enough to carry the weight of the product. The surface should be even and it is important that the measuring points you are considering, are well aligned.
Width measurement
Measure the width at three points; at the top, in the middle and at the bottom. If the measurements deviate, please use the smallest one and deduct according to the chart below, in order to calculate your system width. When measuring for Roller Blinds, it is sufficient to measure the width at the top.
Height measurement
Measure the height at three points; to the left, in the middle and on the right. If the measurements deviate, please use the smallest one and deduct according to the chart below, in order to calculate your system height.
| Recommended deductions | Width | Height |
|---|---|---|
| Panel System | -10 mm | -15 mm |
| Roller Blinds | -5 mm | -0 mm |
| System R & Vertical Blinds | -10 mm | -20 mm |
| System W | -5 mm | -0 mm |
| Venetian Blinds | -10 mm | ** |
** The production height of Venetian Blinds is dependent on the pitch within the ladder cords and therefore, an exact height cannot be guaranteed. You can choose to order by sending us your height measurement without deduction and letting us know whether you prefer your blind to be ”Plus”, meaning that the blind will be at least as high as the height measurement prior to deduction or ”Minus” if you want to make sure that the blind is guaranteed not to sit on the floor, window board etc. when pulled down.
Ann Idstein AB
Dalby 541, DALBY, Sweden
Phone +46 46 14 03 70
info@annidstein.com