Many products within the Ann Idstein product range are based on the use of horizontal slats but there are situations where a vertical slat has clear benefits. The vertical slats are slid aside rather than pulled up or down, which means that no stack of slats is created above or in front of the window. Vertical slats can cover a full window front, offering protection against the sun whilst still offering a view outside by tilting the slats.
System R is based on 250 mm wide vertical slats and apart from the slat width, it shares its components with our regular Vertical Blinds in 89 and 127 mm width. Based on the fitting situation, there is always is slat width that fits. The 250 mm wide System R slats can also be equipped with wooden slats, that are applied horizontally on top of the fabric. There is a wide range of both solid wooden slats and laquered slats in a multitude of colours.
The combination of a 250 wide slat and Ann Idstein’s felt material creates a functional and acoustically efficient room divider. Felt material is both robust and easy to maintain. The system can be fitted to a wall- or ceiling and the rail and components are available in white or anodized aluminium. The 89 and 127 mm slats can also be used for slope ceilings with an angle of up to 60 degrees.
Start by checking that the surface is suitable for the purpose of fitting a blind. Make sure that fittings can be properly attached and that the surface is strong enough to carry the weight of the product. The surface should be even and it is important that the measuring points you are considering, are well aligned.
Width measurement
1. When fitting a free hanging product:
Measure the desired width of the ready made product and use
this measurement as your system width when ordering.
2. When fitting a product from wall to wall:
Measure the width at three points; at the top, in the middle
and at the bottom. If the measurements deviate, please use the
smallest one and deduct according to the chart below, in order
to calculate your system width. When measuring for Roller
Blinds, it is sufficient to measure the width at the top.
Height measurement
1. When fitting a free hanging product:
Measure the height from the ceiling or from a point on the wall
to the point where you want the lower edge of the product to
be. Use this measurement as your system height.
2. When fitting a product from wall to wall:
Measure the height at three points; to the left, in the middle
and on the right. If the measurements deviate, please use the
smallest one and deduct according to the chart below, in order
to calculate your system height.
Recommended deductions
Width
Height
Panel System
-10 mm
-15 mm
Roller Blinds
-5 mm
-0 mm
System R & Vertical Blinds
-10 mm
-20 mm
System W
-5 mm
-0 mm
Venetian Blinds
-10 mm
**
** The production height of Venetian Blinds is dependent on the pitch within the ladder cords and therefore, an exact height cannot be guaranteed. You can choose to order by sending us your height measurement without deduction and letting us know whether you prefer your blind to be ”Plus”, meaning that the blind will be at least as high as the height measurement prior to deduction or ”Minus” if you want to make sure that the blind is guaranteed not to sit on the floor, window board etc. when pulled down.
Fitting in a recess
Before you measure
Start by checking that the surface is suitable for the purpose of fitting a blind. Make sure that fittings can be properly attached and that the surface is strong enough to carry the weight of the product. The surface should be even and it is important that the measuring points you are considering, are well aligned.
Width measurement
Measure the width at three points; at the top, in the middle and at the bottom. If the measurements deviate, please use the smallest one and deduct according to the chart below, in order to calculate your system width. When measuring for Roller Blinds, it is sufficient to measure the width at the top.
Height measurement
Measure the height at three points; to the left, in the middle and on the right. If the measurements deviate, please use the smallest one and deduct according to the chart below, in order to calculate your system height.
Recommended deductions
Width
Height
Panel System
-10 mm
-15 mm
Roller Blinds
-5 mm
-0 mm
System R & Vertical Blinds
-10 mm
-20 mm
System W
-5 mm
-0 mm
Venetian Blinds
-10 mm
**
** The production height of Venetian Blinds is dependent on the pitch within the ladder cords and therefore, an exact height cannot be guaranteed. You can choose to order by sending us your height measurement without deduction and letting us know whether you prefer your blind to be ”Plus”, meaning that the blind will be at least as high as the height measurement prior to deduction or ”Minus” if you want to make sure that the blind is guaranteed not to sit on the floor, window board etc. when pulled down.
